Sort by:
2pcs x SK8 Linear Rail Shaft Guide Support Bracket For 3D Printer Bearing CNC Step Motor
SK8 8MM linear bearing rail support XYZ Shaft Table CNC Router SH8A design End Support is used mainly to support Hard Chrome Plated Rods in CNC Routers, CNC Engraving machines,...
High Temperature NTC 100K Thermistor with 1 Meter Cable (1 pcs)
This is High-Temperature NTC 100K Thermistor with 1 Meter Cable for 3D Printer Reprap. The thermistor is thermally sensitive resistors known for exhibiting a large change in resistance with only...
MK8 single nozzle head extruder aluminum block DIY kit for 3d printer Makerbot
This is a high-quality MK8 Extruder Replacement Aluminum Alloy Block. Use it to replace your blocked/damaged extruder. This block comes in a kit form and requires assembly by the user....
Glass-sealed 100K ohm NTC 3950 Thermistors 1%
Glass-sealed 100K Ohm NTC 3950 Thermistors 1% (NTC-Negative Temperature Coefficient), these thermistors are small, high quality, epoxy encapsulated, precision devices. These epoxy-coated interchangeable chip thermistors offer true interchangeability over wide...
E3D V6 All metal J-head V6 Hotend Full Kit, 1.75/3mm Direct V6 Wade Extruder
E3D-v6: Smaller - Easier - Higher Performance.The E3D-v6 has been redesigned from the ground up. E3D has invested a lot of time and used all of their experience to design...
2 pcs x Thermistor 100k NTC with 1 meter cable , temperature sensor 3d printer
This is Thermistor 100k NTC with 1 Meter Cable Temperature Sensor for 3D Printer Reprap. The thermistor is a thermally sensitive resistor known for exhibiting a large change in resistance with only...
Teflon Tubing For 3D Printers 1.75mm Filament 1m (1 pcs)
The 2x4mm Teflon Tubing – For 3D Printers 1.75mm Filament good corrosion resistance and high insulation resistance. High or low-temperature resistance. It has unique lubricity and the surface is no...
MK8 Extruder Drive Gear 26Teeth 11x11mm for 3D Printer Makerbot 1.75Filament
3D Printer MK8 Extruder Gear / Drive Gear / Extrusion Wheel 26 Teeth 11x11mm is suitable for 1.75 mm. filament. This extruder gear are widely used in desktop FDM 3D...
6x20mm 1 Meter 24V 40W Ceramic Cartridge Heater Wire For 3D Printer Reprap | Ceramic Cartridge for 3d printer |3D Printer Project
24V 40W Reprap Cartridge Heater Wire consists of a cylindrical stainless steel tube and thus provides high corrosion prevention.The heating wire inside which is wound onto a ceramic core. The...
Double Head 2 in 1 out J-Head Remote Extruder 3D Printers Extrusion Parts Hot End All Metal Heat Sink 1.75mm 0.4mm Bowden Part
This is Double Head 2 in 1 out J-Head Remote Extruder 3D Printers Extrusion Parts Hot End All Metal Heat Sink 1.75mm 0.4mm Bowden Part. All Metal Hotend Extruder for...
New V6 Heating Block Compatible with PT100 Sensor for 3d printer (2 pcs)
This New V6 Heating Block Compatible with PT100 sensor allows you to use our new thermistor cartridges, as well as high temperature, high accuracy PT100 temperature sensors. These are the...
Pneumatic Connectors 1.75mm PTFE Tube quick coupler j-head Hotend Fitting
This is Pneumatic Connectors 1.75mm PTFE Tube quick coupler j-head Hotend Fitting. High-Quality: Crafted with precision using top-grade materials, our PC4-01 Pneumatic Connectors are built to last. These connectors are made...